|
Post by squeeker7 on Jan 9, 2011 4:56:32 GMT -6
Does anyone have experience using Kotton Klenser? I received a jug of it and the directions are kind of vague. Says "apply with a brush" but not much else. Tnx
|
|
|
Post by barnettrp21122 on Jan 9, 2011 9:54:48 GMT -6
I'm quoting from my old container of Kotton Klenser: "How To Use on Fine Wood" Caution: To get the results you desire from Kotton Klenser products, always begin with an unnoticeable spot on the piece first. Regular Kotton Klenser-like other products-can remove a finish if not handled with care. REJUVENATING ORIGINAL OIL, WAX OR VARNISH FINISH ON WOODS Step 1- Apply Regular KOTTON KLENSER with hands or paintbrush (in case of heavily dirt-coated or damaged finishes apply with 4/0 steel Wool). Leave on a few minutes or only long enough to clean; wipe off thoroughly. In cases of stubborn dirt, rub with 4/0 steel wool; repeat process if necessary. Step 2- Apply Protective Wood Feeder with hands or brush. Let Feeder absorb into the wood for 6 to 12 hours. If wood absorbs the first coat immediately reapply Feeder. After wood has absorbed the fine oils and conditioners wipe off excess Feeder and and buff following grain of wood with 4/0 steel wool. Step 3- Maintain the beautiful finish with regular applications of KOTTON KLENSER Lemon Oit Beeswax Polish. End of directions.. My own thoughts: Steps 2 and 3 obviously have the user continue with the KOTTON KLENSER products. People who have used Kotton Klenser usually recommend that a cleaned wood surface be allowed to sit for a week or more before applying oil or wax products. Kotton Klenser softens the finish as it removes surface dirt, so follow their recommendation in trying a small hidden portion first. I used a 3-inch paint brush to apply, leaving it on for only about 10 minutes, and then wiping it off with a soft paper towel or clean rag. You'll be surprised how much brown gook comes off, especially with the first application! I'd avoid using steel wool. You risk removing the finish and color along with the dirt, and then you're in a whole new layer of trouble! The majority of people seem to agree that GoJo creme hand cleaner, WITHOUT PUMICE, is nearly of the same makeup as Kotton Klenser, and costs much less. It's widely available in hardward stores. Either cleaner will do a very nice job cleaning just about any hard surface that won't be damaged with some temporary moisture. You can also use them as hand cleaners! Bob PS I highly recommend anyone read "The Furniture Doctor" by George Grotz. It's available in softcover, and is one of the best books covering all the facts and myths of furniture finishes and restoration. The guy's a hoot, too!
|
|
|
Post by squeeker7 on Jan 9, 2011 10:58:00 GMT -6
Thanks for the info. Interesting tidbit about the GoJo. I'm going to give that a try on an old piece.
|
|
|
Post by 3victrolas on Jan 9, 2011 20:26:52 GMT -6
A word of warning concerning the GoJo cleaner. I used that product on some late 1800s fireplace mantles as described above. It worked great for me because I used a light touch. I then had my son & a friend clean the last mantle while I worked on a different cleaning project. They really worked it over & ended up removing the original finish. I've never tried the Kotton Klenser, but the GoJo does work just be sure to go easy with it!
Sharon
|
|
|
Post by phonogfp on Jan 9, 2011 20:45:48 GMT -6
3 Victrolas is right about exercising caution with these products. I haven't had any problems with GoJo, but Kotton Klenser will eat away old decals if given a chance. It will also remove the blue stripes on Firesides if left on too long. The key for either product is repeated, short applications - - perhaps 90-120 seconds each.
George P.
|
|
|
Post by eckster on Jan 10, 2011 22:31:13 GMT -6
Certain wool waxes work good on old wood it seals the wood and repels moisture. A product called fluid film is good for springs in spring motors and prevents oxidation of metals
|
|
|
Post by squeeker7 on Jan 31, 2011 22:37:02 GMT -6
Well used the Kotton Kleanser on my Columbia buffet table victrola and it did a great job. after I did the whole table gave it a good wax job and the machine looks great. Very easy to work with.
|
|